SMC Networks SMC8624/48T Instrukcja Użytkownika Strona 132
- Strona / 556
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
C
ONFIGURING
THE
S
WITCH
3-84
Configuring Interface Connections
You can use the Port Configuration or Trunk Configuration page to
enable/disable an interface, set auto-negotiation and the interface
capabilities to advertise, or manually fix the speed, duplex mode, and flow
control.
Command Attributes
• Name – Allows you to label an interface. (Range: 1-64 characters)
• Admin – Allows you to manually disable an interface. You can disable
an interface due to abnormal behavior (e.g., excessive collisions), and
then reenable it after the problem has been resolved. You may also
disable an interface for security reasons.
• Speed/Duplex – Allows you to manually set the port speed and
duplex mode.
• Flow Control – Allows automatic or manual selection of flow control.
• Autonegotiation (Port Capabilities) – Allows auto-negotiation to be
enabled/disabled. When auto-negotiation is enabled, you need to
specify the capabilities to be advertised. When auto-negotiation is
disabled, you can force the settings for speed, mode, and flow control.
The following capabilities are supported.
- 10half - Supports 10 Mbps half-duplex operation
- 10full - Supports 10 Mbps full-duplex operation
- 100half - Supports 100 Mbps half-duplex operation
- 100full - Supports 100 Mbps full-duplex operation
- 1000full - Supports 1000 Mbps full-duplex operation
- Sym (Gigabit only) - Check this item to transmit and receive pause
frames, or clear it to auto-negotiate the sender and receiver for
asymmetric pause frames. (The current switch chip only supports symmetric
pause frames.)
- FC - Supports flow control
- TigerSwitch 10/100/1000 1
- Management Guide 3
- NTRODUCTION 25
- Table 1-1. Key Features 26
- ESCRIPTION 27
- System Defaults 31
- Table 1-2. System Defaults 32
- Required Connections 36
- ONNECTING 37
- Basic Configuration 38
- Setting Passwords 39
- Setting an IP Address 40
- Dynamic Configuration 41
- Community Strings 43
- Saving Configuration Settings 45
- Managing System Files 46
- AVIGATING 51
- Table 3-2. Main Menu 53
- Manual Configuration 67
- Using DHCP/BOOTP 68
- Managing Firmware 70
- Resetting the System 74
- Setting the System Clock 75
- User Authentication 81
- Configuring HTTPS 86
- Configuring the Secure Shell 89
- Generating the Host Key Pair 91
- Generate 93
- Configuring the SSH Server 94
- Configuring Port Security 96
- ONFIGURING 100
- Command Attributes 101
- UTHENTICATION 105
- Console(config-if)# 106
- Table 3-4. 802.1x Statistics 107
- Access Control Lists 108
- Command Usage 109
- Setting the ACL Name and Type 109
- Configuring a Standard IP ACL 111
- Console(config-std-acl)# 115
- Console(config-mac-acl)# 117
- Configuring ACL Masks 118
- Configuring an IP ACL Mask 119
- Configuring a MAC ACL Mask 122
- Filtering Management Access 126
- Port Configuration 128
- Field Attributes (CLI) 129
- Basic information: 129
- Configuration: 129
- Current status: 130
- ONFIGURATION 131
- Creating Trunk Groups 134
- Configuring LACP Parameters 139
- Displaying LACP Port Counters 142
- Counter Information 142
- Table 3-6. LACP Settings 144
- Configuring Port Mirroring 151
- Configuring Rate Limits 152
- Command Attribute 153
- Showing Port Statistics 154
- Table 3-8. Port Statistics 155
- Address Table Settings 160
- Displaying the Address Table 162
- Changing the Aging Time 163
- LGORITHM 165
- Field Attributes 166
- Displaying Interface Settings 174
- VLAN Configuration 189
- Assigning Ports to VLANs 190
- VA: VLAN Aware 191
- VU: VLAN Unaware 191
- Displaying Current VLANs 195
- Command Attributes (CLI) 196
- Creating VLANs 197
- Configuring Private VLANs 206
- Configuring Protocol Groups 208
- Mapping Protocols to VLANs 209
- Multicast Filtering 229
- ULTICAST 233
- ILTERING 233
- Figure 3-85. Configuring DNS 240
- Web – Select DNS, Cache 244
- NTERFACE 245
- Telnet Connection 246
- Entering Commands 248
- Command Completion 249
- Getting Help on Commands 249
- Showing Commands 250
- Table 4-1. Command Modes 252
- Configuration Commands 253
- Command Line Processing 255
- Command Groups 256
- Line Commands 258
- Console(config)#line console 259
- Console(config-line)# 259
- General Commands 270
- Console>enable 271
- Console# 271
- Console(config)#exit 275
- Console#exit 275
- Press ENTER to start session 275
- User Access Verification 275
- Username: 275
- System Management Commands 276
- Device Designation Commands 277
- User Access Commands 278
- ANAGEMENT 279
- IP Filter Commands 281
- Web Server Commands 284
- Secure Shell Commands 289
- Console#show ssh 299
- Table 4-13. SSH Information 300
- Event Logging Commands 302
- Name Level Description 304
- SMTP Alert Commands 309
- Time Commands 314
- System Status Commands 321
- Example 323
- Related Commands 323
- Frame Size Commands 328
- Flash/File Commands 329
- Authentication Commands 337
- RADIUS Client 339
- TACACS+ Client 343
- Port Security Commands 346
- 802.1x Port Authentication 348
- Access Control List Commands 358
- IP ACLs 360
- Table 4-27. IP ACL Commands 361
- Console(config-ext-acl)# 366
- permit host 10.1.1.21 367
- IP ingress mask ACL: 373
- mask host any 373
- mask 255.255.255.0 any 373
- Priority01234567 375
- Queue12034567 375
- Table 4-28. MAC ACL Commands 379
- Console#show mac access-list 383
- MAC access-list jerry: 383
- Console#show mac access-group 389
- Interface ethernet 1/5 389
- MAC access-list M5 out 389
- ACL Information 392
- SNMP Commands 393
- Console(config)# 395
- DNS Commands 401
- Console(config)#clear host * 403
- Command Mode 410
- Privileged Exec 410
- Interface Commands 412
- Mirror Port Commands 428
- Rate Limit Commands 430
- Link Aggregation Commands 432
- GGREGATION 433
- Address Table Commands 445
- Aging time: 300 sec 449
- Spanning Tree Commands 450
- 452
- Console(config-mstp)# 459
- VLAN Commands 476
- Console(config)#vlan database 477
- Console(config-vlan)# 477
- Configuring VLAN Interfaces 479
- Displaying VLAN Information 487
- Console(config)#pvlan 494
- XTENSION 495
- Priority Commands 500
- Priority Commands (Layer 2) 501
- Queue01234567 505
- Priority20134567 505
- Default Setting 508
- Console(config)#map ip port 509
- IP Precedence Value 01234567 511
- CoS Value 01234567 511
- Multicast Filtering Commands 517
- IGMP Query Commands (Layer 2) 522
- IP Interface Commands 529
- PECIFICATIONS 537
- Management Features 539
- Standards 539
- Management Information Bases 540
- ROUBLESHOOTING 541
- Glossary-1 543
- Glossary-2 544
- Glossary-3 545
- Glossary-4 546
- Glossary-5 547
- Glossary-6 548
- Glossary-7 549
- Glossary-8 550
- Numerics 551
Powiązane produkty i podręczniki dla Switche sieciowe SMC Networks SMC8624/48T
(518 strony)
(56 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.109 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji