Smc-networks ETHERNET/IP EX9-AC -7 Instrukcja Użytkownika

Reduced wiring systemEX250-SEN1Instruction ManualEtherNet/IP™ Compatible SI UnitURL http://www.smcworld.comSpecifications are subject to change withou

16 1712345678ON10IP address192.168.0.X1010101200111130000114000011Remote control *1X32114DHCP mode *2SW1CommunicationsettingCLEAR/HOLDManual set up of

18 19Input Block Model Indication MethodEX250 IEBlock type123Input points : 2, M12 connector (2pcs.)Input points : 4, M12 connector (2pcs.)Input poin

20 21WiringEX250-IE3EX250-IE1/2EX250-IE1(M12 connector, 5 pin, Socket)EX250-IE2(M12 connector, 5 pin, Socket)*1) Input No.1 is connected to the pin No

22 23Display/SettingEX250-IE1EX250-IE2/IE30011EX250EX25000112233EX250EX250Display DescriptionPWRLights up Power supply for sensor is ON.Off Power supp

24 25Part NamesTie-rod (2 pcs.)AccessoryTie-rod (2 pcs.)AccessoryWaterproof cap(for socket)(1 pc.)Dimensions ( unit : mm )59.872.621Output Block59.880

26 27Wiring ( continued )Output connector pin layoutEX9-OET1, EX9-OEP1(M12 connector, 5 pin, Socket)Output No.1 *1Output No.0NC *21 NC *23 GND5 NC

28 29Wiring ( continued )M12 connector, 5 pin, Reverse key1 Power supply for output (24VDC)2 Power supply for output (0VDC)5 Ground( 3 Power suppl

30 31Wiring ( continued )DisplayOutput BlockPWRPWRPower BlockThe Power Supply Cable (for Power Supply Connector of Power Block) is a bypasscable which

32 33Option ( continued )Waterproof CapMounted on the unused ports of the Input Block, Output Block and Power Block.The proper use of this Waterproof

34Troubleshooting ( continued )MS LED statusNormal status : Green light ONFatal failure : Red light ON1The effect of noise is possible. Checkthe insta

ContentsThank you for purchasing the SMC reduced wiring system EX250 series.Please read this instruction manual carefully and understand the contents

2 3SAFETYThe body of unit and this manual contain the essential information for the protection ofusers and others from possible injury and property da

4 5Product SummaryPower supply for Output Block (for high wattage load)24VDCConnecting to bus at upper level(EtherNet/IP)Power supply for output/input

6 7SI Unit Model Indication MethodTie-rod (2 pcs.)AccessoryNote1 : For wiring method, refer to subsection "Wiring" (page 12) in this manual

8 9Mounting/Installation (continued )Layout of the Input BlockPosition the Input Block on the left side of the SI Unit.Layout of the EX9 series Output

10 11SpecificationsSensorinput area1 0I/O mappingOffset(word)Input dataMSB LSB MSB LSB15 8 7001Input area mapping15 14L : Fixed to LowItem Status Cond

12 13Wiring43211342M1212+Rx3-Tx4-Rx12345678ShieldRJ456.747.3 452000Model No. : EX9-AC020EN-PSRJ+TxWiring diagramCable core wire external colorTerminal

14 15Wiring ( continued )24VDC24VDCBrown : 24VDC (for solenoid valves/output)White : 0V (for solenoid valves/output)Grey : EarthBlue : 24VDC (fo